A Federal Pacific panel is not banned or recalled. In 1983 the U.S. Consumer Product Safety Commission (CPSC) closed its investigation without ruling the breakers safe or unsafe. Its testing did find that the breakers failed some lab tests, so have a licensed electrician look at yours.
A breaker panel is the box that sends power from the street to each circuit in your home. A breaker is the switch that shuts a circuit off when it carries too much current. Federal Pacific Electric, often shortened to FPE, made a line of these called Stab-Lok.
Key Takeaways
- A Federal Pacific panel is not banned or recalled.
- In 1983 the CPSC closed its investigation without a safety ruling. It neither cleared nor condemned these panels.
- CPSC testing found that FPE breakers failed some UL calibration tests.
- Look for “Federal Pacific”, “FPE” or “Stab-Lok” on the panel door or the breakers.
- Do not swap breakers yourself. Have a licensed electrician check the panel.
- Edison follows the New Jersey Uniform Construction Code, so a replacement needs a permit and an inspection.
How do I know if I have a Federal Pacific panel?
Look for “Federal Pacific”, “FPE” or “Stab-Lok” printed on the panel door or on the breakers.
What you can safely check
- Open only the outer door. Never take off the metal cover behind it.
- Read the label and the names on the breakers.
- Take a clear photo of what you see.
- Note any burning smell, scorch marks or a warm door.
Can’t tell? An electrician can identify the panel in a short visit.
What did the CPSC actually find?
The CPSC said its data “does not establish that the circuit breakers pose a serious risk of injury.” It also confirmed that FPE breakers failed certain UL calibration tests. The agency could not link those failures to a hazardous situation at that time.
It closed the case without a safety ruling, and it noted that limited funds shaped that decision. So the CPSC did not clear these panels and did not condemn them. It left the question open.
Is a Federal Pacific panel safe to keep using?
The honest answer is that nobody can promise either way. A breaker’s job is to trip when a circuit is overloaded, and lab tests found that these breakers missed some trip tests. That is the reason to get yours checked.
The CPSC’s own advice applies to every panel. If a breaker trips, find out why. Do not simply reset it again and again. When in doubt, ask a licensed electrician.
Can I replace just the breakers?
Do not swap breakers yourself. Breakers must match the panel they sit in, and a wrong match is a hazard of its own. An electrician can tell you whether to replace one breaker or the whole panel.
What should I know about Edison homes and permits?
Edison follows the New Jersey Uniform Construction Code. A panel replacement generally works like this:
- Your electrician submits a construction permit application and the Electrical Subcode Technical Section form (Form F120) with the panel details.
- The township approves the permit before the work starts.
- The electrician coordinates any service disconnection, meter work or upgrade with your electric utility. PSE&G lists Edison Township in its electric service territory. Check your electric bill to confirm your utility.
- After the replacement, the township inspects the electrical work.
- If meter work or reconnection is involved, PSE&G needs the local electrical approval, which it calls a “cut-in card”, before it installs meters and connects service.
We could not confirm how to book an inspection in Edison, so ask the township’s construction office. Official pages: Edison Township construction code, NJ construction permit forms and PSE&G inspection and connection requirements.
Illustrative example
A mid-1960s split-level had a 100-amp Federal Pacific Stab-Lok panel. One breaker fit loosely on the bus and showed heat marks. A visual check cannot show whether breakers will trip correctly, so the panel was replaced with a new 100-amp panel and matching breakers. The load calculation did not call for a bigger service.
An example of a typical job, not a specific Blue Moon customer.
When should I call an electrician about a Federal Pacific panel?
Call to book a check once you confirm the brand. You do not have to wait for a problem.
Call right away if you notice
- A breaker that trips again and again
- A breaker that will not reset
- A burning smell near the panel
- Scorch marks or melted plastic
- Buzzing or crackling from the panel
Next step
If you think you have a Federal Pacific panel, send us a photo of the label or call (213) 322-0128. A licensed Blue Moon electrician can check it and explain your options. See our electrician in Edison, NJ page for more.
Source: CPSC, Commission closes investigation of FPE circuit breakers (March 3, 1983)
